MULTILIFT XR S User And Maintenance Manual Download Page 99

Page: 99 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

14.

Closing body locks

- close the body locks by pressing

the ”bodylocks close” button

- the signal light “locks not closed”

should go out.

14.

Closing body locks

- body locks close when the control

lever is released

- the “locks not closed” signal light

on the control unit goes out.

Move and lock the liftframe to the stowage in accordance with sections

”Moving the liftframe onto the XR21S stowage” and ”Locking the liftframe to

the stowage”, unless the ISO container to be lifted is in the immediate vicinity

of the vehicle.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands