MULTILIFT XR S User And Maintenance Manual Download Page 131

Page: 131 / 210

XR21S59 CHU

131

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Opening ISO container locks

1. The container is locked in the back with TWISTLOCKS. Open these

first

Rotate the tightening wheel counter clockwise. Rotating first loosens the locks

and finally the clasp is turned 90° into lengthwise position and it may be

released from the container corner box.

2. The front of the container is attached with ratchets from the liftframe to the

XR21S equipment stowage. Open these locks

after

the TWISTLOCKS.

First rotate the middle sections of the ratchets enough to loosen them. Detach

the ratchet shafts from the attachment brackets on the liftframe from both

sides of the truck. Attach the ratchets to fastening pins on the inner sides of the

lower sides of the stowage with linch pins.

RELEASE THE RATCHET

ATTACHMENT JOINTS

FROM THE LIFTFRAME

BRACKETS AND MOVE THEM

STOWAGE

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands