MULTILIFT XR S User And Maintenance Manual Download Page 147

Page: 147 / 210

XR21S59 CHU

147

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Lowering the liftframe to the ground

6.1 - continue the movement until the lower corners of the liftframe touch the

ground

6.2 - stop the movement by releasing the control lever.

Monitor the lower ends of the liftframe during the movement.

If the body is in danger of colliding with the rear rollers, stop the

movement before colliding and drive the horizontal movement

upwards.

Drive the middle frame back

- drive the middle frame back by moving the control lever back

(main cylinders out).

- ”frame not down” signal light is lit, when the middle frame is lifted off the

subframe.

MAKE SURE THAT THE GROUND IS FIRM! A liftframe support

sinking may cause the frame to fall over.

If necessary, place e.g. a piece of plank under the support.

Supporting the liftframe

Support the liftframe using heavy wooden or metal supports!

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands