MULTILIFT XR S User And Maintenance Manual Download Page 149

Page: 149 / 210

XR21S59 CHU

149

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

No maintenance work may be carried out

on a liftframe supported by stand supports!

Free from the liftframe

Manual mode A5

is selected.

8.1. Open the hook safety lock by pressing its release button.

Make sure that the lock opens.

If it doesn’t lift the middle frame slightly by moving the control lever

forward. Open the safety lock.

8.2. Keep the safety lock button pressed and drive the middle frame slightly

backwards by moving the control lever backwards. Monitor the hook being

released from the gripping bar on the liftframe.

DO NOT TIP THE LIFTFRAME OVER!

8.3. Drive the truck forward if the hook has been released from the gripping bar.

Release the safety lock button. The lock will close in 10 s. Activate the handbrake.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands