MULTILIFT XR S User And Maintenance Manual Download Page 29

Page: 29 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Tipping

If the flatrack/body overhang is too much, the rear end of the flatrack/body will touch the

ground when tipping and the flatrack/body, truck or hooklift equipment will be damaged.

In very cold weather the load might freeze tight on the flatrack/body. In that case it must

be freed before tipping. Note that the load might come out in large chunks!

NEVER TIP UNDER THE FOLLOWING CIRCUMSTANCES:

• Flatrack/body is top heavy at the front end or at either side.

• Load is frozen or only partially loose

• Ground is slippery or uneven

• Strong side wind, which exceeds over 20 m/s

If it is necessary to drive with the tipping device up, pay attention to the vicinity regarding

the height of the hooklift equipment / flatrack/body with respect to the surroundings like

bridges, tunnels and overhead power lines! Drive slowly and be extra careful.

If the tipping angle is changed during driving, the gearbox bears an extra burden, and the

truck can make unexpected motions on a slippery surface.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands