MULTILIFT XR S User And Maintenance Manual Download Page 162

Page: 162 / 210

XR21S59 CHU

162

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Switch and signal light of hydraulic body locks

Locking hooks

Open

in intermediate

open

body locks

position

body locks

The body locks are opened by pressing the switch in the control unit. A illuminated lock signal

light on the control unit means that the body locks are not fully closed. When in traffic, no

driving or tipping is to be commenced if the light is on. Remove the element obstructing the

locks, or if they are obstructed by the lock pocket in the flatrack/body frame beam, check

that the flatrack/body is correctly positioned on top of the hook device.

Signal light comes on

Signal light illuminated

Intermittent signal light

Signal light goes out

Signal light off

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands