MULTILIFT XR S User And Maintenance Manual Download Page 43

Page: 43 / 210

XR21S59 CHU

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

CXXX

dXXX

>>>>>

12.

Middle frame forward

(beginning of the movement)

- move the control lever forward

- the main cylinder piston rods

move inwards.

12.

Middle frame forward

(beginning of the movement)

- move the control lever forward

- the main cylinder piston rods

move inwards.

Safety codes

A short flatrack/body may accidentally collide with the rear rollers during loading. The

darkened part of the flatrack/body in the picture should not come in contact with the rear

rollers of the rear beam. The situation can be prevented by lifting the flatrack/body with

horizontal movement.

Note!

Horizontal movement during loading can only be done

in manual mode A5

12A.

Horizontal movement during loading

(only in manual mode A5).

Select manual mode A5

- push the A5 button for approx. 2 s.

Drive the telescope cylinder out

- by pushing the front button in the bottom row on the either side of the control unit

- release the button when the front of the flatrack/body has visibly risen above

the rear rollers.

Continue the movement of phase 12 in phase 13 after raising the flatrack/body.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands