MULTILIFT XR S User And Maintenance Manual Download Page 150

Page: 150 / 210

XR21S59 CHU

150

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

Middle frame forward

- drive the middle frame forward by holding the control lever in the front (main

cylinders in)

- “frame not down” signal light on the control unit goes out, when the middle frame

comes down.

10.

Horizontal movement forward

- drive the horizontal movement forward by pushing the front button in the

bottom row on the either side of the control unit (telescope cylinder out)

- horizontal movement comes to the flatrack home position

(approx. 350 mm from the stow/unstow position of horizontal movement).

11.

Closing body and tipping locks

- logic closes the body and tipping locks automatically as the control unit is

released at the end of the horizontal movement

- when the locks are engaged fully, their signal light will go out.

12.

Shut off the oil supply of the hydraulic pump.

13.

Check that all signal lights of the control unit have gone out.

You are now ready to pick up your next container.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands