MULTILIFT XR S User And Maintenance Manual Download Page 178

Page: 178 / 210

XR21S59 CHU

178

1/2018

113813003

Hooklift Multilift XR21S59 CHU

Service Manual

General inspection

Check:

• steel construction for deformations and breakages

• hooklift fastening to the truck chassis, for breakages and loose bolts

• fastening of the rear rollers. Check the securings of all shafts.

• surfaces of piston rods. If the chromium surface of the rod is damaged, especially if

the scratches are longitudinal, the rod or the whole cylinder must be changed.

• wear rate of the gripping hook. The original thickness of the hook must not be worn

more than 10 %.

• wear rate of the slide pads. The maximum wear of the slide pads is 3 mm, but

already a clearance of over 1 mm between the hook arm and the middle frame

requires adding of space plates or replacement of slide pads.

See the picture on the following pages.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands