MULTILIFT XR S User And Maintenance Manual Download Page 111

Page: 111 / 210

XR21S59 CHU

111

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

>>>

Loading phases

MIDDLE FRAME OF THE XR21S EQUIPMENT RESTS ON THE SUB FRAME AND

THE LIFTFRAME IS IN THE GRIPPING HOOK WHEN STARTING MOVEMENTS

During loading the XR21S equipment is controlled seated from the cabin, using the controls

inside the truck’s cabin.

The recommended pump running speed is between 1000 - 1400 k/min. Let the engine run

at idle speed at the beginning and end of movements and while using the locks.

An ISO container can be loaded in

automatic mode A3

, because the length of IC and

ICC ISO containers (6058 mm) doesn’t require movements in manual mode outside a

safe working area.

The final stage of loading a container with a heavy load (more than 10 t), downwards from

an angle of approx. 20 degrees, should be done in

manual mode A5

, because it enables

horizontal movement forward before lowering the container onto the frame and prevents

the bottom bended by the weight from scraping the body of the XR21S equipment.

>>>

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands