MULTILIFT XR S User And Maintenance Manual Download Page 127

Page: 127 / 210

XR21S59 CHU

127

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

FLAT

TIP

ISO

STO

MAN

URB

19.

Horizontal movement forward

- keep the control lever in front position

- main cylinder piston rods move out

- horizontal movement comes to the container home position (that the corner

locks at the back end of the ISO container meet the TWIST LOCKS at the

back end of the ISO container support rollers).

20.

Closing body locks

The movements have followed each other successively, by holding the control

lever in the front.

- body locks close when the control lever is released

(ISO container is not locked with body locks, locking it is explained in section 24)

- the “locks not closed” signal light on the control unit goes out.

See chapter

Loading a flatrack/body,

sections 18, 19 and 20.

Please note that the body locks do not lock the ISO container to

the XR21S equipment, see locking instruction in section 24.

Note!

When the middle frame is coming down to

floating area, there is a risk that the rear frame

jumps up. If this happens the system stops

and ”d012” can be seen in the display. Move the

sliding arm slowly more forwards or backwards

to get the rear frame down.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands