MULTILIFT XR S User And Maintenance Manual Download Page 172

Page: 172 / 210

XR21S59 CHU

172

1/2018

113813003

Hooklift Multilift XR21S59 CHU

Service Manual

Checking the air filter

Check the condition of the air filter. Clean and replace it as necessary.

Checking the condition of the oil

It is possible to examine ageing and deterioration of the quality of oil in the following

way:

• dark colour is caused by overheating of oil

• milky and/or frothy oil contains water

• water can also be seen in separated oil

• air bubbles in oil are a sign of too little oil or of a leak in suction line

• solid particles indicate a component damage or old oil

• air is a sign of oil ageing as a result of overheating.

If you notice any of the above symptoms in oil, change it according to the following

instructions.

Attention!

Hydraulic oils, especially mineral oils, are hazardous to environment. Therefore, follow all

regulations pertaining to collecting and storing oil. Earth material polluted with oil must be

processed according to relevant instructions.

If several successive containers switches are performed, the hydraulic oil may

overheat (>60ºC) making it necessary to install an oil cooler to the system.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands