MULTILIFT XR S User And Maintenance Manual Download Page 158

Page: 158 / 210

XR21S59 CHU

158

1/2018

113813003

Hooklift Multilift XR21S59 CHU

User Manual

The correct operation of the safety lock must be checked

regularly and the shaft nipple greased every month.

•

Open the safety lock of the gripping

hook by pressing button on the

control unit immediately before

lowering the front end of the container

the

ground.

•

Stop the main cylinder when the

container reaches the ground.

•

Check that the safety lock is still open.

If the safety lock has closed, it may

cause the safety lock or the gripping

bar to be damaged when the hook is

pressed down on the gripping bar.

•

Continue the downward motion of the

main cylinders, with the safety lock

open, until the hook is released from

the gripping bar.

•

Drive the vehicle forward, away from

the

container.

See

section

“unloading”.

Summary of Contents for XR S



















































































































































































































Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands

MULTILIFT XR S, User And Maintenance Manual

Search results

Summary of Contents for XR S

Reviews:

Related manuals for XR S

Brands by name

Popular brands