Moxa Technologies AirWorks AWK-1131A User Manual Download Page 7 | Manualshive

Page: 7 / 82

background image

AirWorks AWK-1131A

Introduction

1-3

Product Specifications

WLAN Interface

Standards:

IEEE 802.11a/b/g/n for Wireless LAN
IEEE 802.11i for Wireless Security
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X)
IEEE 802.3ab for 1000BaseT

Spread Spectrum and Modulation (typical):

• DSSS with DBPSK, DQPSK, CCK
• OFDM with BPSK, QPSK, 16QAM, 64QAM
• 802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps,
  DBPSK @ 1 Mbps
• 802.11a/g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps,
  QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps
• 802.11n: 64QAM @ 300 Mbps to BPSK @ 6.5 Mbps (multiple rates
  supported)

Operating Channels (central frequency):

US:
2.412 to 2.462 GHz (11 channels)
5.180 to 5.240 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.700 GHz (11 channels)*
5.745 to 5.825 GHz (5 channels)
EU:
2.412 to 2.472 GHz (13 channels)
5.180 to 5.240 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.700 GHz (11 channels)*
JP:
2.412 to 2.484 GHz (14 channels, DSSS)
5.180 to 5.240 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.700 GHz (11 channels)*
KR:
2.412 to 2.472 GHz (13 channels)
5.180 to 5.320 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.640 GHz (8 channels)*
ANZ:
2.412 to 2.472 GHz (13 channels)
5.180 to 5.320 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.720 GHz (9 channels- excludes 5.600 to 5.640 GHz)*
5.475 to 5.825 GHz (4 channels)
CN:
2.412 to 2.472 GHz (13 channels)
5.180 to 5.320 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.745 to 5.825 GHz (5 channels)

*DFS (Dynamic Frequency Selection) channel support - under AP mode, when radar signal is detected, device
will automatically switch to another channel. However according to the regulation, after switching channel

60

seconds

of availability check period is required before starting service.

«
...
5
6
7
8
9
...
»

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

Brand: Zenitel Pages: 29

Brand: Maipu Pages: 34

Brand: Xsense Connectivity Pages: 56

Brand: MachPower Pages: 26

Brand: Billion Pages: 61

Brand: D-Link Pages: 12

Brand: D-Link Pages: 9

Wireless VPN Router DI-824VUP

Brand: D-Link Pages: 18

Brand: D-Link Pages: 50

RangeBooster N DIR-628

Brand: D-Link Pages: 104

Brand: Airlinkplus Pages: 4

Brand: Airlink101 Pages: 44

Brand: Airlink101 Pages: 48

Brand: Airlink101 Pages: 66

AV TR 3 WIRELESS MULTIROOM AUDIO VIDEO LINK

Brand: Vivanco Pages: 27

Brand: Vivanco Pages: 40

Brand: Westermo Pages: 28

Brand: Intellinet Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands