Moxa Technologies AirWorks AWK-1131A User Manual Download Page 36 | Manualshive

Page: 36 / 82

background image

AirWorks AWK-1131A

Web Console Configuration

3-19

Transmission power

Setting

Description

Factory Default

Available power

Users can manually select a target power to mask max output
power. Because different transmission rates would have their
own max output power, please reference product datasheet.

10 dBm

Beacon interval (for AP/Master mode only)

Setting

Description

Factory Default

Beacon Interval
(40 to 1000 ms)

Indicates the frequency interval of the beacon

100 (ms)

Inactive timeout (for AP mode only)

Setting

Description

Factory Default

1 to 240 seconds

Specifies how long before access point starts sending out client
alive packets

60 seconds

DTIM interval (for AP/Master mode only)

Setting

Description

Factory Default

Data Beacon Rate
(1 to 15)

Indicates how often the AWK-1131A sends out a Delivery
Traffic Indication Message

1

Fragmentation threshold

Setting

Description

Factory Default

Fragment Length
(256 to 2346)

Specifies the maximum size a data packet before splitting and
creating another new packet

2346

RTS threshold

Setting

Description

Factory Default

RTS/CTS Threshold
(256 to 2346)

Determines how large a packet can be before the access point
coordinates transmission and reception to ensure efficient
communication

2346

NOTE

You can refer to the related glossaries in Appendix A for detailed information about the above-mentioned
settings. By setting these parameters properly, you can better tune the performance of your wireless network.

Antenna

Setting

Description

Factory Default

A/B/Both

Specifies the output antenna port. Setting “Antenna” to “Both”
allows 2x2 MIMO communication under 802.11n and 2T2R*
communication in legacy 802.11a/b/g modes.

Both

*Note: 2T2R is different from 802.11n’s multiple spatial data stream (2x2 MIMO), which doubles the
throughput. 2T2R transmits/receives the same piece of data on both the antenna ports.

WMM

Setting

Description

Factory Default

Enable/Disable

WMM is a QoS standard for WLAN traffic. Voice and video data
will be given priority bandwidth when enabled with WMM
supported wireless clients.
Note: WMM will always be enabled under 802.11n mode.

Enable

Turbo Roaming (for Client mode only)

Setting

Description

Factory Default

Enable/ Disable

Moxa’s Turbo Roaming can enable rapid handover when the
AWK-1131A, as a client, roams among a group of APs.

Disable

«
...
34
35
36
37
38
...
»

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

Brand: OEM Pages: 9

Brand: CIS Pages: 27

Brand: NC-link Pages: 13

Brand: Ebyte Pages: 10

Brand: wattsonic Pages: 60

Brand: Aruba Pages: 2

Brand: Tenda Pages: 80

Brand: WIDCOMM Pages: 41

Brand: Silvercrest Pages: 20

Brand: Silvercrest Pages: 66

Brand: PoeWit Pages: 5

Brand: Draytek Pages: 140

Brand: Cambium Networks Pages: 24

Brand: Cambium Networks Pages: 56

Brand: Cambium Networks Pages: 76

Brand: AirLive Pages: 139

Brand: AAxeon Pages: 14

Overdrive Pro 3G

Brand: Sierra Wireless Pages: 174

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands