Moxa Technologies AirWorks AWK-1131A User Manual Download Page 15 | Manualshive

Page: 15 / 82

background image

AirWorks AWK-1131A

Getting Started

2-3

NOTE

After you click

Submit

to apply changes the web page is refreshed (indicated by an “

(Updated)”

status

appearing next to the title) and a blinking reminder to restart the device of the new settings to take effect, will
be shown on the upper-right corner of the web page:

To activate the changes click

Restart

and then

Save and Restart

after you change the settings. About 30

seconds are needed for the AWK-1131A to complete the reboot procedure.

•

Step 5: Select the AWK-1131A operation mode.

By default, the AWK-1131A’s operation mode is set to AP. You can change to Client mode in

Wireless LAN

Setup



Operation Mode

. Detailed information about configuring the AWK-1131A’s operation can be

found in Chapter 3.

•

Step 6: Test communications.

In the following sections we describe two test methods that can be used to ensure that a network
connection has been established.

Communication Testing

After installing the AWK-1131A you can run a sample test to make sure the AWK-1131A and wireless
connection are functioning normally. Two testing methods are described below. Use the first method if you are
using only one AWK-1131A device, and use the second method if you are using two or more AWK-1131A units.

How to Test One AWK-1131A

If you are only using one AWK-1131A, you will need a second notebook computer equipped with a WLAN card.
Configure the WLAN card to connect to the AWK-1131A (NOTE: the default SSID is

MOXA

), and change the IP

address of the second notebook (Notebook B) so that it is on the same subnet as the first notebook (Notebook
A), which is connected to the AWK-1131A.

After configuring the WLAN card, establish a wireless connection with the AWK-1131A and open a DOS window
on Notebook B. At the prompt, type

ping

<IP address of notebook A>

and then press

Enter

(see the figure below). A “Reply from IP address …” response means the communication

was successful. A “Request timed out.” response means the communication failed. In this case, recheck the
configuration to make sure the connections are correct.

«
...
13
14
15
16
17
...
»

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

Brand: Homefibre Pages: 2

Brand: TP-Link Pages: 2

Brand: TP-Link Pages: 85

Brand: Ubiquiti Pages: 24

UniFi AP FlexHD

Brand: Ubiquiti Pages: 22

TginkPad EM160R-GL

Brand: Lenovo Pages: 33

Brand: Streamax Pages: 23

Brand: LYNKSYS Pages: 499

Brand: DQ Technology Pages: 43

Brand: Allied Telesis Pages: 180

Brand: EnGenius Pages: 3

Technicolor DWA0120

Brand: Home Telecom Pages: 14

Brand: Xirrus Pages: 36

Brand: AirLinkWiFi Pages: 62

JWNR2000 - Wireless- N 300 Router

Brand: NETGEAR Pages: 144

Brand: Draytek Pages: 1

Brand: Draytek Pages: 2

Brand: CheckBox Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands