Moxa Technologies AirWorks AWK-1131A User Manual Download Page 53 | Manualshive

Page: 53 / 82

background image

AirWorks AWK-1131A

Web Console Configuration

3-36

System Status

The system status section indicates the status of the device memory and CPU usage in the current device.

NOTE

A CPU overload can result in a watchdog-triggered reboot of the system. Factors such as a high number of
firewall rules (IP/MAC/Protocol filters) and traffic PPS (packet per second) contribute to the rise in CPU usage.

Network Status

The network status section indicates the network status of the device with respect to ARP, bridge status, LLDP,
and the routing table.

ARP Table

Address Resolution Protocol (ARP) Table - indicates the current IP to MAC address mapping for the device.

Bridge Status

Indicates the current status of the network bridge on the device. The interfaces and the corresponding MAC
addresses in this section are the entry points for ingress traffic.

«
...
51
52
53
54
55
...
»

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

Brand: D-Link Pages: 3

Brand: Cambium Pages: 103

Brand: Z-Com Pages: 23

Brand: EnGenius Pages: 2

STEVAL-SPBT4ATV3

Brand: ST Pages: 9

Brand: MikroTik Pages: 4

Brand: TP-Link Pages: 94

NUCLIAS CONNECT DAP-2680

Brand: D-Link Pages: 48

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: D-Link Pages: 25

Brand: D-Link Pages: 26

nuclias connect DAP-2662

Brand: D-Link Pages: 12

Nuclias Connect DAP-2622

Brand: D-Link Pages: 86

Brand: D-Link Pages: 18

Nuclias Connect DAP-2622

Brand: D-Link Pages: 8

Nuclias DBA-2520P

Brand: D-Link Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands