Moxa Technologies AirWorks AWK-1131A User Manual Download Page 9

Page: 9 / 82

AirWorks AWK-1131A

Introduction

1-5

Protocol Support

General Protocols:

Proxy ARP, DNS, HTTP, HTTPS, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, DHCP,LLDP

Interface

Default Antennas:

2 dual-band omni-directional antennas, 2 dBi, RP-SMA (male)

Connector for External Antennas:

RP-SMA (female)

LAN Ports:

1, RJ45, 10/100/1000BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDI-X

connection

Console Port:

RS-232 (RJ45-type)

Reset:

Present

LED Indicators:

PWR, FAULT, STATE, SIGNAL*, WLAN, 10/100/1000 (RJ45 port)

*signal strength indicator

Physical Characteristics

Housing:

Metal, IP30 protection

Weight:

307 g (0.68 lb)

Dimensions:

58 x 115 x 70 mm (2.29 x 4.53 x 2.76 in)

Installation:

DIN-rail mounting (standard), wall mounting (optional)

Environmental Limits

Operating Temperature:

Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)

Storage Temperature:

-40 to 85°C (-40 to 185°F)

Ambient Relative Humidity:

5% to 95% (non-condensing)

Power Requirements

Input Voltage:

12 to 48 VDC, redundant dual DC power inputs

Connector:

4-pin removable terminal block, 500 V insulation

Power Consumption:

6.96 W

Reverse Polarity Protection:

Present

Standards and Certifications

Safety:

UL 60950-1, EN 60950-1

EMC:

EN 55032/55024

EMS:

IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000-4-6 CS: 3 V
IEC 61000-4-8

Radio:

EN 301 489-1/17, EN 300 328, EN 301 893, TELEC, FCC ID SLE-WAPN008, KC, RCM, ANATEL, WPC,

SRRC, IC ID, ICASA, FAC

Note: Please check Moxa’s website for the most up-to-date certification status.

Reliability

MTBF (mean time between failures)
Time:

810,022 hrs

Standard:

Telcordia SR332

Warranty

Warranty Period:

5 years

Details:

See www.moxa.com/support/warranty.aspx

Summary of Contents for AirWorks AWK-1131A


















































































Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-1131A, User Manual

Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands