Moxa Technologies AirWorks AWK-1131A User Manual Download Page 51

Page: 51 / 82

AirWorks AWK-1131A

Web Console Configuration

3-34

Associated Client List (for AP/Master mode only)

The Associated Client List shows all the clients that are currently associated with a particular AWK-1131A. This
page provides useful information for easier network diagnosis:

MAC Address:

Displays the associated client MAC address. If DHCP server is enabled on this AP/Master, the IP

address will also be displayed.

Connection Duration:

States how long the client has been connecting to this AP/Master.

SNR:

States the Signal-Noise Ratio of the associated client. This is especially useful for identifying a weak

signal client that is potentially reducing the overall wireless performance.

Tx (Bytes/Pkts):

Records the AP-to-client traffic after a client is associated.

Rx (Bytes/Pkts):

Records the client-to-AP traffic after a client is associated.

DHCP Client List (for AP mode only)

The DHCP Client List shows all the clients that require and have successfully received IP assignments. You can
click the

Refresh

button to refresh the list.

You can press

Select all

button to select all content in the list for further editing.

Summary of Contents for AirWorks AWK-1131A


















































































Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-1131A, User Manual

Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands