Moxa Technologies AirWorks AWK-1131A User Manual Download Page 39 | Manualshive

Page: 39 / 82

background image

AirWorks AWK-1131A

Web Console Configuration

3-22

Advanced Setup

Several advanced functions are available to increase the functionality of your AWK-1131A and wireless network
system. The DHCP server helps you deploy wireless clients efficiently. Packet filters provide security
mechanisms, such as firewalls, in different network layers. And, SNMP support can make network management
easier.

DHCP Server (for AP mode only)

DHCP (Dynamic Host Configuration Protocol) is a networking protocol that allows administrators to assign
temporary IP addresses to network computers by “leasing” an IP address to a user for a limited amount of time,
instead of assigning permanent IP addresses.

The AWK-1131A can act as a simplified DHCP server and easily assign IP addresses to your DHCP clients by
responding to the DHCP requests from the client ends. The IP-related parameters you set on this page will also
be sent to the client.

You can also assign a static IP address to a specific client by entering its MAC address. The AWK-1131A
provides a

Static DHCP mapping

list with up to 16 entities. Be reminded to check the

Active

check box for

each entity to activate the setting.

You can check the IP assignment status under

Status



DHCP Client List

.

DHCP server

Setting

Description

Factory Default

Enable

Enables AWK-1131A as a DHCP server

Disable

Disable

Disable DHCP server function

Default gateway

Setting

Description

Factory Default

IP address of a default
gateway

The IP address of the router that connects to an outside
network

None

«
...
37
38
39
40
41
...
»

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

Brand: Cambium Networks Pages: 5

Brand: Cambium Networks Pages: 44

Brand: Ruckus Wireless Pages: 3

Brand: NETGEAR Pages: 263

Brand: Konig Pages: 41

Brand: D-Link Pages: 40

Brand: D-Link Pages: 46

Brand: D-Link Pages: 24

Brand: D-Link Pages: 23

DWL-3140AP - Web Smart PoE Thin Access Point

Brand: D-Link Pages: 72

Brand: D-Link Pages: 46

DWL-2130AP - xStack - Wireless Access Point

Brand: D-Link Pages: 12

Brand: D-Link Pages: 8

DWL-2230AP - xStack - Wireless Access Point

Brand: D-Link Pages: 12

DWL-2100AP - AirPlus Xtreme G

Brand: D-Link Pages: 2

Brand: D-Link Pages: 8

Brand: D-Link Pages: 5

DWL-3200AP - AirPremier - Wireless Access Point

Brand: D-Link Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands