Moxa Technologies AirWorks AWK-1131A User Manual Download Page 29 | Manualshive

Page: 29 / 82

background image

AirWorks AWK-1131A

Web Console Configuration

3-12

Security mode

Setting

Description

Factory Default

Open

No authentication

Open

WEP

Static WEP is used

WPA

WPA is used

WPA2

Fully supports IEEE 802.11i with “TKIP/AES + 802.1X”

Open

For security reasons, you should NOT set security mode to Open System because authentication and data
encryption are not performed in Open System mode.

WEP (only for legacy mode)

NOTE

Moxa includes WEP security mode only for legacy purposes. WEP is highly insecure and is considered fully
deprecated by the Wi-Fi alliance. We do not recommend the use of WEP security under any circumstances.

According to the IEEE 802.11
standard, WEP can be used for
authentication and data encryption
to maintain confidentiality. Shared
(or Shared Key) authentication type
is used if WEP authentication and
data encryption are both needed.
Normally, Open (or Open System)
authentication type is used when
WEP data encryption is run with
authentication.

When WEP is enabled as a security
mode, the length of a key (so-called
WEP seed) can be specified in

64/128 bits, which is actually a 40/104-bit secret key with a 24-bit initialization vector. The AWK-1131A
provides 4 entities of WEP key settings that can be selected to use with

Key index

. The selected key setting

specifies the key to be used as a

send-key

for encrypting traffic from the AP side to the wireless client side. All

4 WEP keys are used as

receive-keys

to decrypt traffic from the wireless client side to the AP side.

The WEP key can be presented in two

Key types

, HEX and ASCII. Each ASCII character has 8 bits, so a 40-bit

(or 64-bit) WEP key contains 5 characters, and a 104-bit (or 128-bit) key has 13 characters. In hex, each
character uses 4 bits, so a 40-bit key has 10 hex characters, and a 128-bit key has 26 characters.

Authentication type

Setting

Description

Factory Default

Open

Data encryption is enabled, but without authentication

Open

Shared

Data encryption and authentication are both enabled.

Key type

Setting

Description

Factory Default

HEX

Specifies WEP keys in hex-decimal number form

HEX

ASCII

Specifies WEP keys in ASCII form

Key length

Setting

Description

Factory Default

64 bits

Uses 40-bit secret keys with 24-bit initialization vector

64 bits

128 bits

Uses 104-bit secret key with 24-bit initialization vector

«
...
27
28
29
30
31
...
»

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

Brand: D-Link Pages: 59

Brand: D-Link Pages: 24

Brand: D-Link Pages: 24

Brand: Tenda Pages: 30

Brand: Trango Broadband Wireless Pages: 52

Brand: Linksys Pages: 1122

Brand: Linksys Pages: 1334

Brand: Ajoho Pages: 24

Brand: Uniwill Pages: 27

Brand: Delton Pages: 60

Brand: Delton Pages: 60

Brand: 6Harmonics Pages: 31

Brand: 3Com Pages: 52

Brand: 3Com Pages: 56

Brand: Zio Pages: 38

Brand: X-Micro Pages: 42

Brand: Icidu Pages: 12

Brand: GL-INET Pages: 152

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands