Moxa Technologies AirWorks AWK-1131A User Manual Download Page 25

Page: 25 / 82

AirWorks AWK-1131A

Web Console Configuration

3-8

Operation Mode

The AWK-1131A supports three operation modes—AP, Client, and Sniffer—each of which plays a distinct role
on the wireless network.

Wireless enable

Setting

Description

Factory Default

Enable/Disable

The radio frequency (RF) module can be manually turned on or
off.

Enable

Operation mode

Setting

Description

Factory Default

The AWK-1131A plays the role of a wireless access point

Client

The AWK-1131A plays the role of wireless Client

Sniffer

Turns the device into a remote Wireshark interface to capture
802.11 packets for analysis.

Sniffer mode instructions:

Set operation mode to Sniffer mode on the AWK-1131A and then save/reboot the device.

Connect the AWK-1131A to a laptop with Wireshark installed (v1.12.0 or later release) via Ethernet.

Add a remote interface by entering the IP address of the AWK-1131A.

Detailed Wireshark instructions can be found at:

https://www.wireshark.org/docs/wsug_html_chunked/ChCapInterfaceRemoteSection.html

Start capturing 802.11 wireless packets with Wireshark.

Summary of Contents for AirWorks AWK-1131A


















































































Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-1131A, User Manual

Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands