Moxa Technologies AirWorks AWK-1131A User Manual Download Page 11 | Manualshive

Page: 11 / 82

background image

AirWorks AWK-1131A

Introduction

1-7

The following table summarizes how to read the device’s wireless settings from the LED displays.

LED

Color

State

Description

Front Panel LED Indicators (System)

PWR

Green

On

Power is being supplied from power input 1&2.

Off

Power is not being supplied from power input 1&2.

FAULT

Red

Blinking (fast at 0.5-sec intervals) Cannot get an IP address from the DHCP server

Blinking (slow at 1-sec intervals) IP address conflict

Off

Error condition does not exist.

STATE

Green/

Red

Green

Software Ready

Green/Blinking at 1-sec intervals The AWK has been located by AWK Search Utility.

Red

Booting error condition

SIGNAL

(5 LEDs)

Green

On

Signal level(for Client mode only)

Off

WLAN

Green

On

WLAN function is in Client mode and AWK has
established a link with an AP.

Blinking

WLAN data communication is run in Client mode

Off

WLAN is not in Client Mode or AWK has not
established a link with an AP.

Amber

On

WLAN function is in AP mode.

Blinking

WLAN’s data communication is run in AP mode

Off

WLAN is not in use or not working properly

TP Port(RJ45) LED Indicators (Port Interface)

1000M

Green

On

TP port’s 1000Mbps link is active.

Blinking

Data is being transmitted at 1000 Mbps

Off

TP port’s 1000Mbps link is inactive.

10/100M Amber

On

TP port’s 10/100Mbps link is active.

Blinking

Data is being transmitted at 10/100 Mbps

Off

TP port’s 10/100Mbps link is inactive.

ATTENTION

When the system fails to boot, the LEDs for

STATE

(Green),

FAULT

, and

WLAN

will all light up

simultaneously and blink at one-second intervals. This might be due to improper operation or issues such as
an unexpected shutdown while updating the firmware. To instruction on recovering the firmware, refer to the
“Firmware Recovery” section in Chapter 6.

Beeper

The beeper emits two short beeps when the system is ready.

«
...
9
10
11
12
13
...
»

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

Brand: 2N Pages: 3

Brand: EliteConnect Pages: 214

3CRWX315075A - Wireless LAN Managed Access Point...

Brand: 3Com Pages: 16

Brand: Linksys Pages: 123

Brand: Linksys Pages: 49

Brand: Linksys Pages: 70

Brand: SingTel Pages: 13

Brand: Pakedge Device & Software Pages: 57

Brand: CTC Union Pages: 66

Brand: Anycom Pages: 16

Brand: Broadxent Pages: 27

Brand: Quectel Pages: 55

Brand: Icom Pages: 90

Conduit AP MTCAP-868-002A

Brand: Multitech Pages: 30

Brand: PI Manufacturing Pages: 23

Brand: Novatel Pages: 70

Brand: Ebyte Pages: 19

Brand: Deco Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands