Moxa Technologies AirWorks AWK-1131A User Manual Download Page 50

Page: 50 / 82

AirWorks AWK-1131A

Web Console Configuration

3-33

Status

Wireless LAN Status

The status for

802.11 Information

parameters, such as Operation mode and Channel, are shown on the

Wireless Status

page. The status will refresh every 5 seconds if the

Auto Update

box is checked.

Certain values for

802.11 Information

might not be displayed based on the different operation modes

selected. For example, the

Current BSSID, Signal strength,

and

SNR

parameters

are not available in the AP

mode.

It is helpful to use the continuously updated information on this page, such as

Signal strength, Noise floor,

and

SNR

, to monitor the signal strength of the AWK-1131A in Client mode.

Summary of Contents for AirWorks AWK-1131A


















































































Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-1131A, User Manual

Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands