Moxa Technologies AirWorks AWK-1131A User Manual Download Page 55

Page: 55 / 82

AirWorks AWK-1131A

Web Console Configuration

3-38

Ping

helps to diagnose the integrity of wired or wireless networks. By inputting a node’s IP address in the

Destination

field, you can use the

ping

command to make sure it exists and whether or not the access path

is available.

If the node and access path are available, you will see that all packets were successfully transmitted with no
loss.

Otherwise, some, or even all, packets might get lost, as shown in the following figure.

Firmware Upgrade

The AWK-1131A can be enhanced with more value-added functions by installing firmware

upgrades. The latest

firmware is available at Moxa’s download center.

Before running a firmware upgrade, make sure the AWK-1131A is off-line. Click the

Browse

button to specify

the firmware image file and click

Firmware Upgrade and Restart

to start the firmware upgrade. After the

progress bar reaches 100%, the AWK-1131A will reboot itself.

When upgrading your firmware, the AWK-1131A’s other functions are forbidden.

ATTENTION

Please make sure the power source is stable when you upgrade your firmware. An unexpected power breakup
might damage your AWK-1131A.

Summary of Contents for AirWorks AWK-1131A


















































































Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-1131A, User Manual

Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands