manualshive.com logo in svg

Moxa Technologies AirWorks AWK-1131A, User Manual

The Moxa Technologies AirWorks AWK-1131A user manual provides comprehensive instructions for setting up and utilizing this advanced wireless device. Easily accessible for download at no cost on manualshive.com, this manual ensures users have all the information they need to maximize the benefits of the AWK-1131A in their network operations.

Share
Download
background image

AirWorks AWK-1131A 

Software Installation and Configuration 

 

4-5 

6.

 

Click 

Install 

to begin the installation. The setup window will report the progress of the installation. To 

change the installation settings, click 

Back 

and navigate to the previous screen. 

7.

 

Click 

Finish 

to complete the installation of Wireless Search Utility. 

 

Configuring Wireless Search Utility 

The Broadcast Search function is used to locate all AWK-4131A APs that are connected to the same LAN as your 
computer. After locating an AWK-4131A, you will be able to change its IP address. Since the Broadcast Search 
function searches by TCP packet and not IP address, it doesn’t matter if the AWK-4131A is configured as an AP 
or Client. In either case, APs and Clients connected to the LAN will be located, regardless of whether or not they 
are part of the same subnet as the host. 

1.

 

Start the 

Wireless Search Utility

 program. When the Login page appears, select the “Device Search only” 

option to search for devices and to view the configuration of each device. Select the “Device management” 
option to assign IPs, upgrade firmware, and locate devices. 

 

Summary of Contents for AirWorks AWK-1131A



















































































Reviews:

No comments

Related manuals for AirWorks AWK-1131A

D-Link AirPremier N DAP-3690 Reference Manual preview
AirPremier N DAP-3690
Brand: D-Link Pages: 23
D-Link AirPremier N DAP-3690 Quick Install Manual preview
AirPremier N DAP-3690
Brand: D-Link Pages: 8
D-Link AirPremier N DAP-2690 Quick Install Manual preview
AirPremier N DAP-2690
Brand: D-Link Pages: 52
D-Link AirPremier N DAP-2360 Quick Install Manual preview
AirPremier N DAP-2360
Brand: D-Link Pages: 12
D-Link AirPlus DWL-900AP+ Manual preview
AirPlus DWL-900AP+
Brand: D-Link Pages: 64
Calix E7-2 Application Manual preview
E7-2
Brand: Calix Pages: 225
Tenda W541R User Manual preview
W541R
Brand: Tenda Pages: 57
NDC InstantWave NWH660 User Manual preview
InstantWave NWH660
Brand: NDC Pages: 53
Linksys LAPN300 User Manual preview
LAPN300
Brand: Linksys Pages: 112
Linksys MAX-STREAM EA7250 User Manual preview
MAX-STREAM EA7250
Brand: Linksys Pages: 20
Acksys AirBox Series Manual preview
AirBox Series
Brand: Acksys Pages: 36
IP-COM CW500 Setup Manual preview
CW500
Brand: IP-COM Pages: 15
IP-COM W185AP User Manual preview
W185AP
Brand: IP-COM Pages: 63
Cyberoam NetGenie SOHO N300 User Manual preview
NetGenie SOHO N300
Brand: Cyberoam Pages: 81
EnGenius ECB1200 User Manual preview
ECB1200
Brand: EnGenius Pages: 80
EnGenius EOA3630 User Manual preview
EOA3630
Brand: EnGenius Pages: 58
EnGenius ENH700EXT User Manual preview
ENH700EXT
Brand: EnGenius Pages: 67
EnGenius EAP1750H User Manual preview
EAP1750H
Brand: EnGenius Pages: 64

Brands by name

Popular brands

Load more brands