Moxa Technologies AirWorks AWK-1131A User Manual Download Page 27

Page: 27 / 82

AirWorks AWK-1131A

Web Console Configuration

3-10

NOTE

When you switch to

Client

mode, a

Site Survey

button will be available on the Basic WLAN Setup panel. Click

this button to view information about available APs, as shown in the following figure. You can click on the SSID
of an entity and bring the value of its SSID onto the SSID field of the Basic WLAN Setup page. Click the

Refresh

button to update the site-survey table.

RF type

Setting

Description

Factory Default

2.4 GHz

Only supports the IEEE 802.11b standard

B/G/N Mixed

Only supports the IEEE 802.11g standard

B/G Mixed

Supports IEEE 802.11b/g standards, but 802.11g might
operate at a slower speed when 802.11b clients are on the
network

G/N Mixed

Supports IEEE 802.11g/n standards, but 802.11n might
operate at a slower speed when 802.11g clients are on the
network

B/G/N Mixed

Supports IEEE 802.11b/g/n standards, but 802.11g/n might
operate at a slower speed when 802.11b clients are on the
network

N Only (2.4 GHz)

Only supports the 2.4 GHz IEEE 802.11n standard

Summary of Contents for AirWorks AWK-1131A


















































































Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands

Moxa Technologies AirWorks AWK-1131A, User Manual

Search results

Summary of Contents for AirWorks AWK-1131A

Reviews:

Related manuals for AirWorks AWK-1131A

Brands by name

Popular brands