Motorola ColdFire MCF5281 User Manual Download Page 382 | Manualshive

Page: 382 / 816

background image

17-26

MCF5282 User’s Manual

MOTOROLA

Programming Model

17.5.4.2 Interrupt Mask Register (EIMR)

The EIMR register controls which interrupt events are allowed to generate actual interrupts.
All implemented bits in this CSR are read/write. This register is cleared upon a hardware
reset. If the corresponding bits in both the EIR and EIMR registers are set, the interrupt will
be signalled to the CPU. The interrupt signal will remain asserted until a 1 is written to the
EIR bit (write 1 to clear) or a 0 is written to the EIMR bit.

17.5.4.3 Receive Descriptor Active Register (RDAR)

RDAR is a command register, written by the user, that indicates that the receive descriptor
ring has been updated (empty receive buffers have been produced by the driver with the
empty bit set).

Whenever the register is written, the RDAR bit is set. This is independent of the data
actually written by the user. When set, the FEC will poll the receive descriptor ring and
process receive frames (provided ECR[ETHER_EN] is also set). Once the FEC polls a
receive descriptor whose empty bit is not set, then the FEC will clear the RDAR bit and
cease receive descriptor ring polling until the user sets the bit again, signifying that
additional descriptors have been placed into the receive descriptor ring.

31

30

29

28

27

26

25

24

23

22

21

20

19

18

16

Field HBERR BABR BABT GRA TXF TXB RXF RXB

MII EBERR LC

RL

UN

—

Reset

0000_0000_0000_0000

R/W

R/W

15

0

Field

—

Reset

0000_0000_0000_0000

R/W

R/W

Address

0x1008

Figure 17-5. Interrupt Mask

Register (EIMR)

Table 17-13. EIMR Field Descriptions

Bits

Name

Description

31–19

See Figure 17-5

and Table 17-12.

Interrupt mask. Each bit corresponds to an interrupt source defined
by the EIR register. The corresponding EIMR bit determines
whether an interrupt condition can generate an interrupt. At every
processor clock, the EIR samples the signal generated by the
interrupting source. The corresponding EIR bit reflects the state of
the interrupt signal even if the corresponding EIMR bit is set.
0 The corresponding interrupt source is masked.
1 The corresponding interrupt source is not masked.

18–0

—

Reserved, should be cleared.

«
...
380
381
382
383
384
...
»

Summary of Contents for ColdFire MCF5281

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ColdFire MCF5281

Smart-MPPT Li Series

Brand: Y-Solar Pages: 6

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: Jabra Pages: 8

Brand: RadioMaster Pages: 10

Brand: Aurora Pages: 2

Brand: TSM Pages: 2

Brand: Consort Pages: 4

Brand: Variotech Pages: 24

Brand: National Instruments Pages: 3

Brand: Kelly Pages: 43

Brand: SLV Pages: 11

Brand: CLS Pages: 6

Brand: HomeMatic Pages: 68

komplete kontrol s series

Brand: Native Instruments Pages: 338

Brand: Kelly Pages: 36

RG/2MT X Series

Brand: Madas Pages: 28

Brand: Galletti Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands