manualshive.com logo in svg

Motorola ColdFire MCF5281, User Manual

Introducing the Motorola ColdFire MCF5281 - a powerful device designed to meet your technological needs. Ensure optimum utilization of this product with our comprehensive User Manual, available for free download at manualshive.com. Access the manual effortlessly and unleash the full potential of your Motorola ColdFire MCF5281.

Share
Download
background image

6-6

MCF5282 User’s Manual

MOTOROLA

 

Memory Map  

• The FLASHBAR valid bit is programmed according to the chip mode selected at 

reset (see Chapter 30, “Chip Configuration Module (CCM)” for more details). All 
other bits are unaffected.

The FLASHBAR register contains several control fields. These fields are shown in
Figure 6-3

NOTE

The default value of the FLASHBAR is determined by the chip
configuration selected at reset (see Chapter 30, “Chip
Configuration Module (CCM)” for more information). If
external boot mode is used, then the FLASHBAR located in the
processor’s CPU space will be invalid and it must be initialized
with the valid bit set before the CPU (or modules) can access
the on-chip Flash.

NOTE

Flash accesses (reads/writes) by a bus master other than the
core, (DMA controller or Fast Ethernet Controller), or writes to
Flash by the core during programming must use the backdoor
Flash address of IPSBAR plus an offset of 0x0400_0000. For
example, for a DMA transfer from the first location of Flash
when IPSBAR is still at its default location of 0x4000_0000,
the source register would be loaded with 0x4400_0000.
Backdoor access to Flash for reads can be made by the bus
master, but it takes 2 cycles longer than a direct read of the
Flash if using its FLASHBAR address.

NOTE

The Flash is marked as valid on reset based on the RCON (reset
configuration) pin state. Flash space is valid on reset when
booting in single chip mode (RCON pin asserted and
D[26]/D[17]/D[16] set to 110), or when booting internally in
master mode (RCON asserted and D[26]/D[17]/D[16] are set
to 111 and D[18] and D[19] are set to 00). See Chapter 30,
“Chip Configuration Module (CCM)” for more details. When
the default reset configuration is not overriden, the MCF5282
will (by default) boot up in single chip mode and the Flash
space will be marked as valid at address 0x0. The Flash
configuration field is checked during the reset sequence to see
if the Flash is secured. If it is the part will always boot from
internal Flash, since it will be marked as valid, regardless of
what is done for chip configuration.

Summary of Contents for ColdFire MCF5281

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ColdFire MCF5281

Facility Explorer FX Series Installation Instructions preview
FX Series
Brand: Facility Explorer Pages: 4
G1SLE MK2 Alignment Manual preview
MK2
Brand: G1SLE Pages: 2
Lattice Semiconductor HDR-60 User Manual preview
HDR-60
Brand: Lattice Semiconductor Pages: 26
National Instruments sbRIO-9629 Quick Reference Manual preview
sbRIO-9629
Brand: National Instruments Pages: 2
Rain Bird PAR+ES Installation Manual preview
PAR+ES
Brand: Rain Bird Pages: 24
Rain Bird ESP-LXIVM Series Device Installation Manuallines preview
ESP-LXIVM Series
Brand: Rain Bird Pages: 16
Cooper S225-50-45 Service Information preview
S225-50-45
Brand: Cooper Pages: 4
DAYLIFF SUNVERTER B Installation & Operating Manual preview
SUNVERTER B
Brand: DAYLIFF Pages: 40
Halma Alicat Scientific MC Quick Start Manual preview
Alicat Scientific MC
Brand: Halma Pages: 2
Samson TROVIS 5571 Mounting And Operating Instructions preview
TROVIS 5571
Brand: Samson Pages: 44
Beckhoff C6925 Manual preview
C6925
Brand: Beckhoff Pages: 47
DOTECH FX3DH Series Manual preview
FX3DH Series
Brand: DOTECH Pages: 4
MISUMI DS102MS Operation Manual preview
DS102MS
Brand: MISUMI Pages: 166
Sunricher SR-2400P Quick Start Manual preview
SR-2400P
Brand: Sunricher Pages: 2
Darco ERO-32AP-0 V1.4 Instruction Manual And Warranty Card preview
ERO-32AP-0 V1.4
Brand: Darco Pages: 14
Rainmachine Touch HD-12 Quick Start Manual preview
Touch HD-12
Brand: Rainmachine Pages: 22
Monde Synthesizer Ribbonz User Manual preview
Ribbonz
Brand: Monde Synthesizer Pages: 4
Samson Graphite MF8 Quick Start Manual preview
Graphite MF8
Brand: Samson Pages: 64

Brands by name

Popular brands

Load more brands