manualshive.com logo in svg

Motorola ColdFire MCF5281, User Manual

Share
Download
Motorola ColdFire MCF5281 User Manual Download Page 377

MOTOROLA

Chapter 17.  Fast Ethernet Controller (FEC)

  

17-21

Programming Model

17.5.3 MIB Block Counters Memory Map

Table 17-11 defines the MIB Counters memory map which defines the locations in the MIB
RAM space where hardware maintained counters reside. These fall in the 0x1200-0x13FF
address offset range. The counters are divided into two groups. 

RMON counters are included which cover the Ethernet Statistics counters defined in RFC
1757. In addition to the counters defined in the Ethernet Statistics group, a counter is
included to count truncated frames as the FEC only supports frame lengths up to 2047
bytes. The RMON counters are implemented independently for transmit and receive to
insure accurate network statistics when operating in full duplex mode.

IEEE counters are included which support the Mandatory and Recommended counter
packages defined in section 5 of ANSI/IEEE Std. 802.3 (1998 edition). The IEEE Basic
Package objects are supported by the FEC but do not require counters in the MIB block. In
addition, some of the recommended package objects which are supported do not require
MIB counters. Counters for transmit and receive full duplex flow control frames are
included as well.

0x1084

RCR

32

Receive Control Register

0x10C4

TCR

32

Transmit Control Register

0x10E4

PALR

32

Physical Address Low Register

0x10E8

PAUR

32

Physical Address High+ Type Field

0x10EC

OPD

32

 Pause Duration

0x1118

IAUR

32

Upper 32 bits of Individual Hash Table

0x111C

IALR

32

Lower 32 Bits of Individual Hash Table

0x1120

GAUR

32

Upper 32 bits of Group Hash Table

0x1124

GALR

32

Lower 32 bits of Group Hash Table 

0x1144

TFWR

32

Transmit FIFO Watermark

0x114C

FRBR

32

FIFO Receive Bound Register

0x1150

FRSR

32

FIFO Receive FIFO Start Registers

0x1180

ERDSR

32

Pointer to Receive Descriptor Ring

0x1184

ETDSR

32

Pointer to Transmit Descriptor Ring

0x1188

EMRBR

32

Maximum Receive Buffer Size

Table 17-10. FEC Register Memory Map (continued)

IPSBAR

Offset

Name

Width

Description

Summary of Contents for ColdFire MCF5281

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands