manualshive.com logo in svg

Motorola ColdFire MCF5281, User Manual

Share
Download
Motorola ColdFire MCF5281 User Manual Download Page 261

MOTOROLA

Chapter 12.  Chip Select Module

  

12-7

Chip Select Registers

12.4.1.2 Chip Select Mask Registers (CSMR0–CSMR6)

The CSMRs, Figure 12-3, are used to specify the address mask and allowable access types
for the respective chip selects. 

.

Table 12-7 describes CSMR fields.

Table 12-6. CSAR

n

 Field Description

Bits

Name

Description

15–0

BA

Base address. Defines the base address for memory dedicated to chip select CS[6:0]. BA is compared 
to bits 31–16 on the internal address bus to determine if chip select memory is being accessed.

31

16 15

9

8

7

6

5

4

3

2

1

0

Field

BAM

—

WP — AM C/I SC SD UC UD V

Reset

Unitialized

0

R/W

R/W

Addr

0x084 (CSMR0); 0x090 (CSMR1); 0x09C (CSMR2); 0x0A8 (CSMR3); 

0x0B4 (CSMR4); 0x0C0 (CSMR5); 0x0CC (CSMR6)

Figure 12-3.  Chip Select Mask Registers (CSMR

n

)

Table 12-7. CSMR

n 

Field Descriptions

Bits

Name

Description

31–16

BAM

Base address mask. Defines the chip select block by masking address bits. Setting a BAM bit causes 
the corresponding CSAR bit to be ignored in the decode.
0 Corresponding address bit is used in chip select decode.
1 Corresponding address bit is a don’t care in chip select decode.
The block size for CS[6:0] is 2

n

 where  n = (number of bits set in respective CSMR[BAM]) + 16.

So, if CSAR0 = 0x0000 and CSMR0[BAM] = 0x0008, CS0 addresses a 128-Kbyte (2

17

 byte) range 

from 0x0000–0x1_FFFF. 
Likewise, for CS0 to access 32 Mbytes (2

25

 bytes) of address space starting at location 0x0000, and 

for CS1 to access 16 Mbytes (2

24

 bytes) of address space starting after the CS0 space, then  CSAR0 

= 0x0000, CSMR0[BAM] = 0x01FF, CSAR1 = 0x0200, and CSMR1[BAM] = 0x00FF.

8

WP

Write protect. Controls write accesses to the address range in the corresponding CSAR. Attempting 
to write to the range of addresses for which CSAR

n

[WP] = 1 results in the appropriate chip select 

not being selected. No exception occurs.
0 Both read and write accesses are allowed.
1 Only read accesses are allowed.

7

—

Reserved, should be cleared.

6

AM

Alternate master. When AM = 0 during a DMA access, SC, SD, UC, and UD are don’t cares in the 
chip select decode. 

Summary of Contents for ColdFire MCF5281

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands