Motorola ColdFire MCF5281 User Manual Download Page 690 | Manualshive

Page: 690 / 816

background image

29-18

MCF5282 User’s Manual

MOTOROLA

Background Debug Mode (BDM)

29.5.2 BDM Serial Interface

When the CPU is halted and PST reflects the halt status, the development system can send
unrestricted commands to the debug module. The debug module implements a synchronous
protocol using two inputs (DSCLK and DSI) and one output (DSO), where DSO is
specified as a delay relative to the rising edge of the processor clock. See Table 29-1. The
development system serves as the serial communication channel master and must generate
DSCLK.

The serial channel operates at a frequency from DC to 1/5 of the CLKOUT frequency. The
channel uses full-duplex mode, where data is sent and received simultaneously by both
master and slave devices. The transmission consists of 17-bit packets composed of a
status/control bit and a 16-bit data word. As shown in Figure 29-12, all state transitions are
enabled on a rising edge of CLKOUT when DSCLK is high; that is, DSI is sampled and
DSO is driven.

Figure 29-12. BDM Serial Interface Timing

DSCLK and DSI are synchronized inputs. DSCLK acts as a pseudo clock enable and is
sampled on the rising edge of the processor clock as well as the DSI. DSO is delayed from
the DSCLK-enabled CLK rising edge (registered after a BDM state machine state change).
All events in the debug module’s serial state machine are based on the processor clock
rising edge. DSCLK must also be sampled low (on a positive edge of CLK) between each
bit exchange. The MSB is transferred first. Because DSO changes state based on an
internally-recognized rising edge of DSCLK, DSDO cannot be used to indicate the start of
a serial transfer. The development system must count clock cycles in a given transfer.
C1–C4 are described as follows:

• C1—First synchronization cycle for DSI (DSCLK is high).
• C2—Second synchronization cycle for DSI (DSCLK is high).
• C3—BDM state machine changes state depending upon DSI and whether the entire

input data transfer has been transmitted.

• C4—DSO changes to next value.

CLKOUT

DSCLK

Next State

BDM State

Machine

DSO

DSI

Current State

Current

Next

Past

Current

C1

C2

C3

C4

«
...
688
689
690
691
692
...
»

Summary of Contents for ColdFire MCF5281

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ColdFire MCF5281

Brand: H3C Pages: 16

Revolution FA-M3 R

Brand: YOKOGAWA Pages: 57

Brand: Jordan Valve Pages: 5

Brand: Knoll Pages: 2

Boiler Control TSBC

Brand: Thermal Solutions Pages: 48

Brand: Zmotion Pages: 59

MC DC-2.00 Series

Brand: Hanbay Pages: 7

Brand: Thevco Pages: 36

ISaGRAF VP-23W7

Brand: ICP DAS USA Pages: 192

SCZF1 SSR Series

Brand: Ametek Pages: 24

Porter MPC Series

Brand: Parker Pages: 30

Brand: PPA Pages: 2

Brand: Inverter Pages: 2

NetController B042-004

Brand: Tripp Lite Pages: 2

Brand: Yamatake Pages: 156

Brand: Qanon Pages: 10

Brand: Intersil Pages: 8

Artist Transport

Brand: Avid Technology Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands