Motorola ColdFire MCF5281 User Manual Download Page 171 | Manualshive

Page: 171 / 816

background image

MOTOROLA

Chapter 7. Power Management

7-3

Memory Map and Registers

3. The entry into a low-power mode is processed by the low-power mode control

logic, and the appropriate clocks (usually those related to the high-speed processor
core) are disabled.

4. After entering the low-power mode, the interrupt controller enables a

combinational logic path which evaluates any unmasked interrupt requests. The
device waits for an event to generate an interrupt request with a priority level
greater than the value programmed in LPICR[XLPM_IPL[2:0]].

NOTE

Only fixed (external) interrupt can bring a device out of stop
mode. To exit from other low-power modes, such as doze or
wait, either fixed or programmable interrupts may be used;
however, the module generating the interrupt must be enabled
in that particular low-power mode.

5. Once an appropriately-high interrupt request level arrives, the interrupt controller

signals its presence, and the SIM responds by asserting the request to exit
low-power mode.

6. The low-power mode control logic senses the request signal and re-enables the

appropriate clocks.

7. With the processor clocks enabled, the core processes the pending interrupt request.

7

6

4

3

0

Field ENBSTOP

XLPM_IPL[2:0]

—

Reset

1/0

0

1/0

0

Undefined

R/W

R/W

Address

0x012

Figure 7-1. Low-Power Interrupt Control Register (LPICR)

Table 7-2. LPICR Field Description

Bits

Name

Description

7

ENBSTOP

Enable low-power stop mode.
0 Low-power stop mode disabled
1 Low-power stop mode enabled. Once the core is stopped and the signal to enter stop mode is

asserted, processor clocks can be disabled.

6–4

XLPM_IPL[2:0] Exit low-power mode interrupt priority level. This field defines the interrupt priority level needed to

exit the low-power mode.Refer to Table 7-3.

3–0

—

Reserved, should be cleared.

«
...
169
170
171
172
173
...
»

Summary of Contents for ColdFire MCF5281

















































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ColdFire MCF5281

Brand: Federal Signal Corporation Pages: 60

Brand: FASTRON. Pages: 16

Brand: Federal Signal Corporation Pages: 79

Brand: Federal Signal Corporation Pages: 32

Brand: Radware Pages: 98

infi 90 IMMFP12

Brand: Bailey Pages: 75

Brand: EFI Pages: 127

Brand: maxxess Pages: 11

Brand: SOLARJACK Pages: 14

Brand: IFM Pages: 41

Brand: OLYS Pages: 4

The Boost Box WS 1107

Brand: Watersports Innovations Pages: 12

Brand: Parker Pages: 31

Brand: ccei Pages: 16

NetLinx Integrated Controller NI-3100

Brand: AMX Pages: 2

Brand: M-Elec Pages: 2

ACTPRO PRODUCT RANGE

Brand: ACT Pages: 8

Brand: Pellet Grill Outlet Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands