Motorola ColdFire MCF5281 User Manual Download Page 488

Page: 488 / 816

23-14

MCF5282 User’s Manual

MOTOROLA

Register Descriptions

Table 23-9 describes UISR

and UIMR

fields.

23.3.11 UART Baud Rate Generator Registers (UBG1

/UBG2

)

The UBG1

registers hold the MSB, and the UBG2

registers hold the LSB of the preload

value. UBG1

and UBG2

concatenate to provide a divider to the system clock for

transmitter/receiver operation, as described in Section 23.5.1.2.1, “System Clock Baud
Rates.”

Table 23-9. UISR

/UIMR

Field Descriptions

Bits

Name

Description

COS

Change-of-state.
0 UIPCR

[COS] is not selected.

1 Change-of-state occurred on CTS and was programmed in UACR

[IEC] to cause an interrupt.

6–3

—

Reserved, should be cleared.

Delta break.
0 No new break-change condition to report. Section 23.3.5, “UART Command Registers (UCRn),”

describes the

RESET

BREAK

CHANGE

INTERRUPT

command.

1 The receiver detected the beginning or end of a received break.

FFULL/
RxRDY

RxRDY (receiver ready) if UMR1

[FFULL/RxRDY] = 0; FIFO full (FFULL) if

UMR1

[FFULL/RxRDY] = 1. Duplicate of USR

[FFULL/RxRDY]. If FFULL is enabled for UART0

or UART1, DMA channels 2 or 3 are respectively interrupted when the FIFO is full.

TxRDY Transmitter ready. This bit is the duplication of USR

[TxRDY].

0 The transmitter holding register was loaded by the CPU or the transmitter is disabled. Characters

loaded into the transmitter holding register when TxRDY = 0 are not sent.

1 The transmitter holding register is empty and ready to be loaded with a character.

Field

Divider MSB

Reset

0000_0000

R/W

Address

0x218 (UBG10), 0x258 (UBG11), 0x298 (UBG12)

Figure 23-12. UART Baud Rate Generator Register (UBG1

)

Field

Divider LSB

Reset

0000_0000

R/W

Address

0x21C (UBG20), 0x25C (UBG21) 0x29C (UBG22)

Figure 23-13. UART Baud Rate Generator Register (UBG2

)

Summary of Contents for ColdFire MCF5281

















































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ColdFire MCF5281

Reviews:

Brands by name

Popular brands

Motorola ColdFire MCF5281, User Manual

Search results

Summary of Contents for ColdFire MCF5281

Reviews:

Brands by name

Popular brands