Mitel MiVOICE BUSINESS Engineering Manualline Download Page 91 | Manualshive

Page: 91 / 381

background image

Phones and Voice Applications

77

Most external applications emulate 5220 sets and require similar resources when they connect
to the 3300 ICP. They will also use sockets and place monitors on the users’ sets, similar to
the MiCollab Clients and server in the above tables.

The UC Express application connects to the phone for access to call control. All of the UC
Express supported phones have a SAC connection, but may not invoke a monitor. When UC

5304/5312/5324
(without attached
application)

1 per device

1 per device

None

None

2 per device

(MiNET & SAC)

5304/5312/5324
(with attached
application)

1 per device

1 per device

1 per system

(via internal

SAC server)

1 per device

2 per device

(MiNET & SAC)

5304/5312/5324
(without UC
Express)

1 per device

1 per device

None

None

2 per device

(MiNET & SAC)

5304/5312/5324
(with UC Express)

1 per device

1 per device

1 per system

(via internal

SAC server)

None

2 per device

(MiNET & SAC)

5550 Console

1 per device

None

None

None

3 per device

(MiNET & 2

additional

management

connections)

5560

2 per device

2 per device

1 per system

(via internal

SAC server)

2 per device

4 per device

(2 MiNET & 2 SAC)

SIP Phone

None

None

None

None

1 per device (SIP)

Hot Desk User in
SAC (not logged in)

None

None

None

1 per user

(SAC)

(see Note)

None

SAC Server
(always consumed)

None

None

1 per system

None

None

Web Server
(always consumed)

None

None

1 per system

None

None

Note:

Devices that use the SAC Service or Web service will consume an external IP Socket, or IP

port, to connect to these services. The connection from these internal services into the MiTAI/HCI will
consume a MiTAI socket at the server internal connection. This is shown with the devices for
information, but in practice these sockets are always consumed against the services as these are
always active, even without devices to monitor.

Table 28: (continued)ICP Connections (continued)

TELEPHONE OR

APPLICATION

RESOURCE

MINET

SOCKETS

SAC

SOCKETS

MITAI

SOCKETS

MITAI

MONITORS

MIVOICE BUSINE

SS IP

CONNECTIONS

Page 2 of 2

«
...
89
90
91
92
93
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: Neoi Pages: 40

Brand: Samsung Pages: 22

Brand: E-Boda Pages: 50

Brand: Lanix Pages: 13

Brand: Lanix Pages: 25

Brand: Netway Pages: 68

Brand: LifeSize Pages: 12

Brand: Plum Mobile Pages: 15

Brand: AMGOO Pages: 44

Brand: Alcatel Pages: 29

Brand: Evolveo Pages: 23

Brand: Samsung Pages: 159

Brand: Samsung Pages: 171

Brand: Samsung Pages: 158

Brand: Yealink Pages: 5

Brand: TP-Link Pages: 61

Brand: Zte Pages: 156

Brand: Motorola Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands