Mitel MiVOICE BUSINESS Engineering Manualline Download Page 175 | Manualshive

Page: 175 / 381

background image

Licensing

161

Fax over IP (T.38) licenses

5

A T.38 license is required to allow T.38 transmission or reception of Fax
over an IP or SIP trunk when the call path may encounter TDM
interfaces—for example, T1/E1 trunks, analog loop start trunks, or ONS
ports. The T.38 licenses are provisioned in multiples of 4; the minimum
value is 0 and the maximum value is 64.

Compression (TDM/IP)

A Compression license is needed for TDM to IP or IP to TDM calls that
require the use of the DSP compression. One Compression license can
handle up to 8 calls

Teleworker Solution (6010)

One IP device license and one IP user license per phone

Customer Interaction Solutions

1

One IP device license and one IP user license per port to 3300 ICP

HTML Apps Infrastructure Licenses

A license is required to assign HTML applications to a device.

Speech Server

1

One IP device license and one IP user license per port to 3300 ICP

Messaging Server

1

One IP device license and one IP user license per port to 3300 ICP

Hospitality / PMS

Hospitality option

X-NET over TDM

One license to enable X-Net networking over TDM links

Tenanting

Tenanting license

Note 1

: The licenses described are those applicable to the 3300 ICP. The Customer Interaction Solutions,

Speech Server, and Messaging Server also require application licenses to enable their functions.

Note 2:

The number of voice mailboxes is not the same as the number of voice mail ports enabled. The number

of ports required depends on the quantity and duration of calls to the mailboxes and can be adjusted up to the
limit of 30 ports within ESM without changing any licensing.

Note 3:

The IP device licenses limit includes SIP devices.

Note 4:

An Analog Line license is required for ONS ports on the ASU II and the AX. ONS ports on the ASU, the

AMB/AOB, and the PER do not require licenses. SX-200 ONS and OPS sets require an analog line license. DNI
lines do not require a license on either the PER or the Bay.

Note 5:

FAX over IP support requires the DSP II card.

Table 42: Devices and licenses - MCD Release 4.0 and Earlier (continued)

DEVICE

LICENSE

Page 2 of 2

«
...
173
174
175
176
177
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: i.safe MOBILE Pages: 49

Brand: i.safe MOBILE Pages: 37

Brand: Samsung Pages: 145

Brand: Samsung Pages: 123

Brand: Samsung Pages: 167

Brand: M4TEL Pages: 22

Brand: Icemobile Pages: 19

DigiWalker A701

Brand: Mio Pages: 168

Brand: Grandstream Networks Pages: 27

Brand: Sagem Pages: 70

Brand: INQ Pages: 101

SMARTPHONE 3.2 LITE

Brand: Tesla Pages: 3

Brand: Plum Pages: 19

2 VOICE 1083/58

Brand: urmet domus Pages: 60

Brand: Nibe Pages: 32

8900 - Curve - GSM

Brand: Blackberry Pages: 48

Brand: NEC Pages: 74

3205 - Cell Phone - CDMA2000 1X

Brand: Nokia Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands