Mitel MiVOICE BUSINESS Engineering Manualline Download Page 79 | Manualshive

Page: 79 / 381

background image

Phones and Voice Applications

65

DECT (DIGITAL ENHANCED CORDLESS
TELEPHONY)

When multiple DECT base station units (Radio Fixed Part (RFP)) are connected to the 3300
ICP using ISDN (BRI or PRI), the reference clock source in the ICP must be accurate to better
than ± 5 ppm. This allows seamless hand-over between RFP units without loss of connection.
If there is no reference source from the PSTN (which is often better than ± 1 ppm), the local
clock needs to provide this accuracy.

Accuracy can be achieved using a Stratum 3 clock source (± 4.6 ppm), which is standard on
all 3300 controllers.

DECT RFP units with IP connection use their own internal reference clocks. Because local
synchronization takes place between these units directly, the requirements on the ICP are not
as critical.

Refer to “RFC 3942, reclassifying DHCP options: DeTeWe and Spectralink Phones” on
page 243 for information regarding DECT phones and DHCP.

SPECTRALINK PHONES

For information on SpectraLink phones see “Wireless Phone Performance on the 3300 ICP”
on page 262.

Refer to “RFC 3942, reclassifying DHCP options: DeTeWe and Spectralink Phones” on
page 243 for information regarding SpectraLink phones and DHCP.

PHONE STANDS

The Gigabit Ethernet phone stand and the Wireless LAN (WLAN) phone stand can be installed
in place of the regular phone stand on 5200/5300 series IP phones.

MCD Release 4.1 coincided with the introduction of the IP DECT phone stand.

The Wireless LAN phone stand operates with any version of 3300 ICP system software. The
Gigabit Ethernet phone stand operates with 3300 ICPs running system software version 6.1
UR1 and greater.

«
...
77
78
79
80
81
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: D-Link Pages: 6

Brand: Xiaomi Pages: 16

Brand: Samsung Pages: 265

Brand: Sony Ericsson Pages: 208

alcatel Pixi4-7 4G BELL

Brand: TCL Pages: 41

Brand: BenQ Pages: 97

Brand: FLY Pages: 33

Brand: Macronix Pages: 65

Brand: Micromax Pages: 64

Brand: switel Pages: 4

Brand: Samsung Pages: 183

Brand: Garmin Pages: 73

Brand: Haier Pages: 56

Brand: Haier Pages: 98

Brand: QUO Pages: 9

Brand: Zte Pages: 60

Brand: Lava Pages: 2

Brand: Motorola Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands