Mitel MiVOICE BUSINESS Engineering Manualline Download Page 205 | Manualshive

Page: 205 / 381

background image

Bandwidth, Codecs and Compression

191

IP applications and compression

Most Mitel IP-based applications support compression. NuPoint does not support compression.

To get the best voice quality performance from devices such as Speak@Ease™ and IP voice
mail, allocate them in a common compression zone with other devices not running compression,
e.g. default zone 1.

Consider the effect of allocating them to a compression zone where an application is used as
a central resource over a WAN link. Bandwidth restrictions may still require compression to be
enabled.

TRUNKING GATEWAY WORKING EXAMPLE

In terms of considering network bandwidth, it should be based on the 120 channels and where
they are being connected. Also consider the maximum number of compression channels
(G.729a); they are limited to 64 within a single unit. Further IP trunks use standard
non-compressed G.711 channels. Thus, in the example of toll-bypass, it is likely that trunks will
go via the IP WAN. In this case, the connection bandwidth requirements will be 11.0 Mbps. For
a fully G.711 connection (no compression), then 16.0 Mbps is needed. Note that Ethernet and
WAN links should not be fully utilized, in order to allow maintenance traffic to flow. Typically, a
link is loaded to 70% on a WAN link and 80% on a full duplex LAN.

Table 58: Trunk Gateway Bandwidth Calculation with 64 Channels Compression

ADDITION (MIXED COMPRESSED AND
NON-COMPRESSED)

BANDWIDTH

64 channels of compression (40.8k each)

2.611 Mbps

56 channels of non-compression (120-64 = 56, 96.8k each)

5.402 Mbps

Signalling overhead 10% (on total of voice)

0.801 Mbps (10% of 5.402+2.611)

TOTAL (payload)

8.835 Mbps

TOTAL (connections with LAN loading 80%)

11.0 Mbps

Table 59: Trunk Gateway Bandwidth Calculation with 120 Channels Non-compression

ADDITION (NON-COMPRESSED)

BANDWIDTH

120 channels of non-compression (100k each)

11.62 Mbps

Signalling overhead 10%

1.16 Mbps (10% of 11.62)

TOTAL (payload)

12.78 Mbps

TOTAL (connections with LAN loading)

16.0 Mbps

«
...
203
204
205
206
207
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

StarLink Connect Series

Brand: NAPCO Pages: 40

Brand: GE Pages: 40

Brand: Mitsubishi Pages: 72

Brand: Alcatel Pages: 48

Brand: Mobeye Pages: 28

Brand: Manta Pages: 100

Brand: SAIET Pages: 49

Brand: Movilnet Pages: 26

VidyoConference

Brand: Vidyo Pages: 2

Brand: Zte Pages: 198

Brand: Avvio Pages: 28

Brand: Lava Pages: 35

Brand: Ice Mobile Pages: 24

Brand: Zte Pages: 48

Brand: Biamp Pages: 8

Brand: Chinavision Pages: 17

Brand: Bmobile Pages: 18

Brand: Bmobile Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands