Mitel MiVOICE BUSINESS Engineering Manualline Download Page 60 | Manualshive

Page: 60 / 381

background image

Engineering Guidelines

46

SIP PHONES AND USE OF TLS (SIP-TLS)

The use of TLS (Transport Layer Security) places additional requirements on the
MiVoice Business systems (MiVoice Business and 3300 ICP). This introduces additional limits
and considerations to the overall deployment.

The number of SIP-TLS devices that can be deployed may be different from the maximum
number of SIP devices, and is dependent on a number of factors including the number of nodes
in the cluster as well as the number of MiNet phones on the particular node.

The table below is to be used in conjunction with other standard limitation tables in these
Guidelines. The lower value of each of these is to be used. In practice, the SIP-TLS numbers
mainly impact the MiVoice Business for ISS, whereas the 3300 ICPs already have limitations
in place.

For deployments with more than 100 nodes in a cluster where SIP-TLS will be deployed, it is
highly recommended that Professional Services be contacted to get a more specific value on
location and quantity of SIP-TLS devices per node.

Device Campons per
system

172

480 (MXe Server)

Group Campons per
system

84

240 (MXe Server)

Hard Holds per system

312

870 (MXe Server)

Wake-up Calls in 1
minute

100

213 (MXe Server)

Wake-up Calls in 5
minutes

400

852 (MXe Server)

Table 14: SIP-TLS Device Support Limits

NUMBER OF MINET DEVICES

NUMBER OF SIP-TLS DEVICES SUPPORTED PER

QUANTITY OF MINET DEVICES

100 OR FEWER NODE CLUSTER

40 OR FEWER NODE CLUSTER

5000

0

0

4000

400

400

3000

800

800

2000

1200

1200

1000

1500

1600

0

1800

2000

Table 13: Other Maximum Limits (continued)

FEATURE/ RESOURCE

VALUE/QUANTITY

NOTES

Page 2 of 2

«
...
58
59
60
61
62
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: O2 Pages: 72

Brand: Pantech Pages: 145

Brand: Paradox Pages: 44

Brand: T-Mobile Pages: 4

Brand: T-Mobile Pages: 158

Brand: T-Mobile Pages: 212

Brand: Brähler Systems Pages: 25

Brand: Alcatel Pages: 96

Brand: Alcatel Pages: 20

Brand: Leotec Pages: 35

Brand: Blackberry Pages: 17

Brand: Alcatel Pages: 27

Scopia XT5000 Series

Brand: RADVision Pages: 55

Brand: Blu Pages: 28

Brand: Sony Ericsson Pages: 15

Brand: Plum Pages: 21

Brand: Slider Pages: 27

Brand: Sony Ericsson Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands