Mitel MiVOICE BUSINESS Engineering Manualline Download Page 46 | Manualshive

Page: 46 / 381

background image

Engineering Guidelines

32

When determining network bandwidth, consider voice mail sessions as being active 100% of
the time. The number of voice mail sessions determines the bandwidth required. With G.711
voice streams and 30 active sessions, a minimum of 4.0 Mbps must be provided:

(30 x 96.8 kbps + 10% (signalling)) / 80% = 4.0 Mbps

Where the unit is used as a dedicated voice mail server, consider the number of other functions
provided on the box. As more voice mail sessions are activated the number of IP phones that
can be handled decreases. Typically 30 VM sessions and 700 users are in direct opposition.
Consider multiple units beyond approximately 400 users and 20 voice mail sessions.

CONFIGURATION TABLES

The following tables show the maximum capacity for each feature or resource in each type of
controller. You cannot configure a system to support all maximum values at the same time.

•

IP devices includes all telephones and all applications which emulate telephones, including
SIP phones.

•

TDM devices includes all ONS/OPS and DNIC sets but not analog or digital trunks.

•

Compression channels includes only those channels that are necessary within the ICP to
connect TDM ports to IP trunks. Most IP sets can stream compressed audio to another IP
port without using any ICP resources. Those that can’t, simply stream uncompressed audio
(the call is not routed using internal ICP resources).

•

Digital links refers to embedded BRI (4 links, 8 lines or trunks per module), embedded
T1/E1 (1 link, 23/24/30 trunks, or 2 links, 46/48/60 trunks per module), or external T1/E1
(2 links, 46/49/60 trunks per NSU cabinet). It does not include the external BRI NSU, which
is an adapter that can be added behind any E1 link at up to 15 trunks per cabinet.

MXE SERVER, MIVOICE BUSINESS VIRTUAL, MIVOICE BUSINESS
FOR ISS, AND MIVOICE BUSINESS MULTI-INSTANCE

Note:

Other limits besides those in the following table may apply to MiVoice Business

Virtual and MiVoice Business for ISS depending on the deployment. Consult the
MiVoice Business Virtual and MiVoice Business for ISS Engineering Guidelines for more
information.

«
...
44
45
46
47
48
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: Samsung Pages: 337

Brand: Samsung Pages: 158

Brand: BENQ-SIEMENS Pages: 132

SPH-A600 Series

Brand: Samsung Pages: 111

Brand: Catchwell Pages: 101

Brand: Pantech Pages: 90

JANUS SmartView

Brand: Rath Pages: 8

POLYCOM VTXTM 1000

Brand: Polycom Pages: 2

Brand: Videocon Pages: 36

Polycom SoundPoint 550

Brand: PennNet Pages: 11

Brand: Quadro Pages: 125

Brand: M4 Pages: 22

Brand: Allview Pages: 143

Brand: Ericsson Pages: 77

Brand: Ericsson Pages: 71

Brand: Hisense Communications Pages: 24

Brand: Nokia Pages: 107

6185 - Cell Phone - CDMA

Brand: Nokia Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands