Mitel MiVOICE BUSINESS Engineering Manualline Download Page 66

Page: 66 / 381

Engineering Guidelines

PROVISIONING SYSTEM RESOURCES

The table below shows the capacity of each system in its factory default configuration, with no
additional MMC modules or other upgrades purchased

Notes:

No compression is possible in the base configurations.

The AX must have a 4GB flash card installed to support Voice Mail.

Table 18: Standard 3300 ICP Configurations

FEATURE/
RESOURCE

CX II

MXE
STANDARD

MXE SERVER

IP users (note 1)

150

300

400

100

5000

TDM users (note 2)

150

192

ACD users

350

Echo canceller
channels/E2T

64 (128 max)

128

256

Compression channels

Conference channels

128

Voice Mail ports

CIM ports

ASU supported

LS trunks

IP networking (note 3)

yes

Echo slot number

5, 6

Quad DSP slot number

7, 8

Dual FIM slot number

Digital links (T1/E1)

(see note 4)

Peripheral

cabinets

NSU/DSU cabinets

Notes:

1. This is the maximum number of IP users that can be installed without additional DSP resources.

2. This is the maximum number of DNIC and ONS users that can be installed without additional DSP resources.

DNIC users are only supported on MXe and LX systems.

3. The base system can support IP networking but not compression.

4. It is assumed that digital (or analog LS) trunks will be installed in or connected to the controller to access the

PSTN. BRI links should be considered a subset of T1/E1, with 8 voice channels per card (4 BRI links), instead
of 48 T1 or 60 E1 (2 T1/E1 links).

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Search results

Summary of Contents for MiVOICE BUSINESS

Reviews:

Related manuals for MiVOICE BUSINESS

Brands by name

Popular brands

Mitel MiVOICE BUSINESS, Engineering Manualline

Search results

Summary of Contents for MiVOICE BUSINESS

Reviews:

Related manuals for MiVOICE BUSINESS

Brands by name

Popular brands