Mitel MiVOICE BUSINESS Engineering Manualline Download Page 84 | Manualshive

Page: 84 / 381

background image

Engineering Guidelines

70

See http://www.dect.org to determine which variant is appropriate for the country of operation.
For operation in the United States and Canada, use DECT 6.0. Standard DECT is used in the
United Kingdom.

The Standard DECT variant uses 10 RF carrier frequencies, while the DECT 6.0 variant has
only 5. Each RF carrier is then divided into 12 full duplex TDM channels. See table below for
the number of available channels.

To maintain performance and use all available channels, the maximum total number of active
Mitel Cordless (DECT) Handsets and Headsets in a specific area (phones with Cordless
Modules evenly distributed in the area) is shown below. The last column in the table provides
a density guideline for deploying Mitel Cordless (DECT) Handsets and Headsets. This number
is only a guideline - a number of factors, including the size of the installation and the site layout
may allow this density to be exceeded.

Table 25: Cordless Module and Accessory Part Numbers

DESCRIPTION

MITEL PART NUMBER

PART MARKING

Standard DECT Cordless Module

56008567B

56008567B

DECT 6.0 Cordless Module

56008567A

56008567A

Standard DECT Handset

56008564B

56008564B

DECT 6.0 Handset

56008564A

56008564A

Standard DECT Headset

57008904

100-79330049-00

DECT 6.0 Headset

57008905

100-79330059-00

Table 26: DECT Channel Capacity

DESCRIPTION

NUMBER OF AVAILABLE RF

CARRIERS

NUMBER OF AVAILABLE

CHANNELS

Standard DECT (1880 - 1900MHz)

10

120

DECT 6.0 (1920 - 1930MHz)

5

60

Table 27: Maximum Number of Cordless Accessories

DESCRIPTION

TOTAL NUMBER OF

HEADSETS AND

HANDSETS

AREA IN SQUARE

METERS (SQUARE

FEET)

HEADSETS/HANDSETS

PER SQUARE METER

(SQUARE FOOT)

Standard DECT

120

250 (820)

0.476 (0.044)

DECT 6.0

60

762 (2500)

0.265 (0.025)

Note:

Each portable device (Handset or Headset) installed will partially consume a

channel even if it is not on a call - therefore giving each user both a Handset and Headset
counts as two channels used.

Note:

RF energy will travel through floors and ceilings. This can affect deployment

density and performance. When planning an installation across multiple floors,
interference from adjacent floors must be taken into account.

«
...
82
83
84
85
86
...
»

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Reviews:

No comments

Related manuals for MiVOICE BUSINESS

Brand: Janam Pages: 70

Brand: Gigaset Pages: 27

Brand: THOMSON Pages: 81

Brand: DC-Connex Pages: 16

Brand: T-Mobile Pages: 2

Brand: Icemobile Pages: 20

Brand: Avaya Pages: 5

Brand: Trikdis Pages: 22

Brand: DIS Pages: 54

Brand: Salora Pages: 29

Konftel EGO 8105s OmniSound

Brand: Alcatel-Lucent Pages: 20

Brand: IPRO Pages: 53

Brand: Wherify Pages: 37

Brand: Zte Pages: 48

Brand: Xiaomi Pages: 8

Brand: Sharp Pages: 121

Brand: Sharp Pages: 134

Brand: Sharp Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands