Mitel MiVOICE BUSINESS Engineering Manualline Download Page 174

Page: 174 / 381

Engineering Guidelines

160

DEVICE LICENSING

The 3300 ICP requires a number of device licenses in order to operate. The following table lists
these licenses.

Table 42: Devices and licenses - MCD Release 4.0 and Earlier

DEVICE

LICENSE

IP phone

IP device license

User on IP phone

IP user license

User on SIP phone

SIP user license

Resilient User on SIP Phone

SIP user license

User on ONS Phone

Analog line license

CITELink phone

IP user and IP device licenses

User on DNI phone

No license, but counts against total number of users a system can handle

Wireless phone (SpectraLink)

IP user and IP device license

Wireless phone (IP DECT - EMEA)

IP user and IP device license

5602 or 5606 Wireless Handset (IP
DECT - Global)

SIP user license

Resilient phone on secondary
controller

IP device license

Hot Desk user

IP user license

External Hot Desk User

External hot Desk User License

Hot Desk phone

IP device license

Unified Communicator Mobile

One IP device license and one IP user license for each line monitor, call
agent, and TUI agent used in the Unified Communicator Mobile Server

MiCollab Client

None needed

MiCollab Client Softphone

IP user and IP device licenses

ACD Agent

ACD Agent license

Voice Mailbox

Voice Mailbox license (1 per user)

Basic Auto-Attendant

Voice Mailbox license

Multi-Level Auto-Attendant

Voice Mailbox license (1 per node in the tree)

Record-a-Call

Advanced Voice Mail license (system-wide)

Auto Forward to Email

Advanced Voice Mail license

Personal Contacts

Advanced Voice Mail license

Networked Voice Mail, VPIMv2

One Voice Mail Networking license per ICP

NuPoint

One IP device license and one IP user license per port to 3300 ICP

IP Networking (IP trunk)

One IP Networking license needed per ICP to enable IP Trunk calls

Digital trunk (PRI, etc.)

One Network Link license per digital trunk span

Page 1 of 2

Summary of Contents for MiVOICE BUSINESS






























































































































































































































































































































































































Search results

Summary of Contents for MiVOICE BUSINESS

Reviews:

Related manuals for MiVOICE BUSINESS

Brands by name

Popular brands

Mitel MiVOICE BUSINESS, Engineering Manualline

Search results

Summary of Contents for MiVOICE BUSINESS

Reviews:

Related manuals for MiVOICE BUSINESS

Brands by name

Popular brands