MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 94

Page: 94 / 204

Solving Problems

Printing Quality

Symptom

Cause

Solution

Vertical

white lines
appear in
image.

The imaging unit,
transfer roller, or fuser
unit are is
misinstalled, old, or
damaged.

Confirm the proper installation of the items,
and check them for damage. If necessary,
replace them.

Image is
too light;
there is low
image
density.

The media is moist
from humidity.

Remove the moist media and replace with
new, dry media.

One or more toner
cartridges are
defective.

Remove the toner cartridges and check for
damage. If necessary, replace them.

The imaging unit is old
or damaged.

Remove the imaging unit and check for
damage. If necessary, replace it.

Media type may be set
incorrectly.

Envelopes, glossy stock (set as Thick 2 or
Thick 3), labels, and thick stock have to be
set in the correct mode. See “Media” on
page 32.

The printer is
connected to an outlet
with a voltage or
frequency that does
not match the printer
specifications.

Use a power source with the proper
specifications.

Driver settings are
not correct.

Confirm that you are using the correct
driver settings.

Media is the wrong
size.

Check with your documentation to confirm
the correct media size and type.

Unsupported media is
being used.

Check www.minolta-qms.com/support
(click on Answer Base) for currently
approved media. To order approved media,
go to www.q-shop.com.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Search results

Summary of Contents for ENord magicolor 3100

Reviews:

Brands by name

Popular brands

MINOLTA-QMS ENord magicolor 3100, User Manual

Search results

Summary of Contents for ENord magicolor 3100

Reviews:

Brands by name

Popular brands