manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, User Manual

Share
Download
MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 192

TCP/IP Menu

186

TCP/IP Menu

Common

EtherTalk

L A N   M a n a g e r

NetWare

TCP/IP**

Protocol

Subnet

Administration

Communications

Resident NIC

CrownNet

Internet 

Default 

Secure 

 Mask

Router

Address

Files

Community

Internet 

Address

Access

Remove

Passwords

Remove

 Hosts

Optional NIC*

Yes

No

Disabled

Enabled

A ccnting /

Port 

Accnting 

L P D  

RevChan

Assignment

Timeout

Banner

B O O T P

WINS

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Disabled

Enabled

Pri WINS

Sec WINS

NBT

Protocol

Addr**

Addr**

Scope ID

*Optional

** Pri and Sec WINS Addr are IP addresses of the Primary 

and Secondary WINS servers (default 0.0.0.0). Default for 

DHCP and WINS is disabled. NBT Scope ID is any valid DNS 

domain name consisting of 2 dot-separated parts, or a “*” 

(default blank). An empty string (blank value) is ignored.

SNMP 

NMS 1-5

Read
Write
Trap

Read-Trap
None

Write-Trap

Yes

No

Yes

No

Yes

No

Disabled

Enabled

Bold = Default

DHCP

RARP

Note: For more menu details 
and printer configuration
information, refer to the 

CrownBooks

 in PDF on the 

Software Utilities

 CD-ROM.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands