MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 106

Page: 106 / 204

Status, Error, and Service Messages

100

EXTENDED ACC FILE

SIZE BY <

> KB

The <

> (size of the

non-empty
accounting file) has
been increased
successfully.

No action needed.

FRONT COVER OPEN

The cover is open
and must be closed.

Close the cover.

FUSER LIFE LOW

The fuser unit life is
low.

Replace the fuser unit
and media feed roller.

Reset the consumables
count in the Operator
Control/Consumables/
Item Replaced/Fuser
menu

FUSER UNIT

MISSING

The fuser is not fully
seated.

Make sure the fuser is
fully seated.

IDLE

The printer is on line,
but no jobs are in
process.

No action needed.

IMAGING UNIT LIFE

LOW

The imaging unit life
is low.

Replace the imaging
unit.

The imaging unit

will automatically reset
its consumables count.

IMAGING UNIT

MISSING

The imaging unit is
missing.

Make sure that the
imaging unit is correctly
installed.

INITIALIZING

The printer is
initializing.

Wait. No other action
needed.

The printer is
warming up and
getting ready to go on
line.

Wait. No other action
needed.

INVALID <

The item

is not

valid, such as disk
selected or paper
information.

Make sure you are
inputting or choosing the
valid information or
value.

This message...

means...

do this...

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Search results

Summary of Contents for ENord magicolor 3100

Reviews:

Brands by name

Popular brands

MINOLTA-QMS ENord magicolor 3100, User Manual

Search results

Summary of Contents for ENord magicolor 3100

Reviews:

Brands by name

Popular brands