manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, User Manual

Share
Download
MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 88

Solving Problems

82

Other Problems 

Symptom

Cause

Solution

Printer power 
is not on.

The power cord is 
not correctly 
plugged into the 
outlet.

Set the power switch off (O position), then 
remove the power cord from the outlet 
and plug it back in, then set it back to the 
on (I) position.

The power switch 
has not been 
pressed.

Set the power switch to the on (I) 
position.

The power switch is 
not correctly turned 
on (I position).

Set the power switch to the off (O) 
position, then set it back to the on (I) 
position. 

Something is wrong 
with the outlet you 
are using for the 
printer.

Plug another electrical appliance into the 
outlet and see whether it operates 
properly.

The printer is 
connected to an 
outlet with a voltage 
or frequency that 
does not match 
the printer 
specifications.

Use a power source with the 
specifications listed in appendix A of the 

User’s Guide

.

“Printer 
is not 
responding” is 
displayed in 
the print 
monitor.

The printer is in 
energy-saving 
mode.

It takes a little time for printing to start if 
the printer is in energy-saving mode. You 
can change the number of minutes before 
the printer switches to power-saving 
mode in the Administration/Engine/
Energy Saver menu. If you do not want to 
use this mode, disable it in the 
Administration/Engine/Energy Saver 
menu.

Printer takes 
too long to 
start when you 
are replacing 
the imaging 
unit.

The printer takes 
approximately 6 
minutes to warm up 
when a new 
imaging unit is 
installed.

Wait. No action needed.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands