manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, User Manual

Share
Download
MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 52

Loading Media

46

Refilling a Multipurpose Media Tray

1

Take off the top and bottom sheets of a ream of paper. Holding a stack 
of approximately 100 sheets at a time, fan the stack to prevent static 
buildup in the paper before inserting it in a tray. Don’t fan large quantities 
of transparency media.

2

Open the multipurpose tray.

Do not place heavy objects on the 
multipurpose tray.

3

Adjust the media guides to the width 
of the media.

The tray extender supports long 
media.

Attention

åã

Make sure the media fits easily 

between the guides. Improperly 
adjusted guides may cause poor 
print quality, media jams, or 
printer damage.

5

"

Make sure the guides are snug 
enough to keep the media 
straight, but not so tight that it 
buckles.

4

Place the media into the multipurpose 
tray with the printing-side up.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands