manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, User Manual

Share
Download
MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 100

Status, Error, and Service Messages

94

Status, Error, and Service Messages

Status, error, and service messages are displayed in the control panel 
message window. They provide information about your printer and help 
you locate many problems. When the condition associated with a displayed 
message has changed, the message is cleared from the window. Refer to 
the 

CrownBooks

 for further information.

5

"

Status messages are not displayed while the printer is off line.

Status and Error Messages

This message...

means...

do this...

<

COLOR

> TONER 

EMPTY

The 

<

COLOR

>

 toner 

cartridge is empty.

Replace the toner 
cartridge.

 

Open and close the 
printer’s front door. 

Reset the consumables 
count in the Operator 
Control/Consumables/
Item Replaced/

<

COLOR

>

 Toner menu.

<

COLOR

> TONER LOW

The 

<

COLOR

>

 toner 

cartridge is low. 
Printing continues 
even though the 
warning appears. 
Approximately 100 
letter/A4 pages (at 
5% coverage) after 
detecting that toner in 
a cartridge is low, the 
printer displays 

<

COLOR

> TONER 

EMPTY

 in the 

message window, 
and the printer stops.

The color gradually 
fades, so replace the 
toner cartridge as soon 
as possible. 

Do not send very large 
print jobs after the 

TONER LOW

 message is 

displayed. 

Reset the consumables 
count in the Operator 
Control/Consumables/
Item Replaced/

<

COLOR

> 

Toner menu.

<

COLOR

> TONER 

MISSING

The 

<

COLOR

>

 toner 

cartridge is not 
installed properly.

Install the indicated 
toner cartridge.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands