manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, User Manual

Share
Download
MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 54

Loading Media

48

7

Open the multipurpose tray and adjust the media guides to the length and 
width of the envelopes.

Attention

åã

Improperly adjusted guides may cause poor print quality, media 

jams, or printer damage.

8

Fold the flaps.

Make sure the adhesive 
is dry.

9

Place the envelope stack into the 
multipurpose tray with the printing- 
side down. 

Print envelopes on the front address 
side only. Some parts of the 
envelope consist of three layers of 
paper—the front, back, and flap. 
Anything printed in these layered 
regions may be lost or faded. 

5

"

Check your application documentation to determine if the flap 
should be placed on the left or on the right. You can also print a 
single envelope to check the orientation before printing multiple 
copies.

10

Recheck the media guides to make sure they are adjusted to the width of 
the envelopes.

11

Print the envelopes.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands